Description
Features:
- Meanwell SMPS Power Supply
- Universal AC input / Full range
- Built-in active PFC function
- Protections: Short circuit / Overload / Over voltage / Over temperature
- 5″×3″ compact size
- Free air convection for 110w and 160w with 20.5 CFM forced air
- Medical safety approved (2 × MOOP between primary to secondary) (Note.10)
- With power good and fail signal output
- Built-in remote sence funciton for 5~15v
- No load power consumption under 0.75W by PS-ON control (G model)
- Standby 5V 0.8A with fan, 0.6A without fan (G model)
- Fixed switching frequency at 65KHz
- 3 years warranty
Detailes:
|
MODEL |
RPS-75-15 |
|
|
OUTPUT |
DC VOLTAGE |
15V |
|
RATED CURRENT |
5A |
|
|
CURRENT RANGE |
0 ~ 6.7A |
|
|
RATED POWER |
75W |
|
|
PEAK LOAD(23.5CFM) |
100.5W |
|
|
RIPPLE & NOISE (max.) Note.2 |
150mVp-p |
|
|
VOLTAGE ADJ. RANGE |
13.5 ~ 16.5V |
|
|
VOLTAGE TOLERANCE Note.3 |
±1.0% |
|
|
LINE REGULATION |
±0.5% |
|
|
LOAD REGULATION |
±1.0% |
|
|
SETUP, RISE TIME |
500ms, 30ms/230VAC 500ms, 30ms/115VAC at full load |
|
|
HOLD UP TIME (Typ.) |
80ms/230VAC 20ms/115VAC at full load |
|
|
INPUT |
VOLTAGE RANGE |
90 ~ 264VAC 127 ~370VDC |
|
FREQUENCY RANGE |
47 ~ 63Hz |
|
|
EFFICIENCY (Typ.) |
83% |
|
|
AC CURRENT (Typ.) |
1.5A/115VAC 1A/230VAC |
|
|
INRUSH CURRENT(Typ.) |
COLD START 25A/115VAC 50A/230VAC |
|
|
LEAKAGE CURRENT Note.7 |
Earth leakage current < 150£gA/264VAC , Touch current < 100 A/264VAC |
|
|
PROTECTION |
OVERLOAD |
140 ~ 180% rated output power |
|
Protection type : Hiccup mode, recovers automatically after fault condition is removed |
||
|
OVER VOLTAGE |
17.25 ~ 20.25V |
|
|
Protection type : Shut down o/p voltage, re-power on to recover |
||
|
ENVIRONMENT |
WORKING TEMP. |
-20 ~ +70°C(Refer to “Derating Curve”) |
|
WORKING HUMIDITY |
20 ~ 90% RH non-condensing |
|
|
STORAGE TEMP., HUMIDITY |
-40 ~ +85°C, 10 ~ 95% RH |
|
|
TEMP. COEFFICIENT |
±0.03%/°C (0~45°C) |
|
|
VIBRATION |
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes |
|
|
SAFETY & EMC |
SAFETY STANDARDS |
ANSI/AAMI ES60601-1, TUV EN60601-1, IEC60601-1 approved |
|
WITHSTAND VOLTAGE |
I/P-O/P:4KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC |
|
|
ISOLATION RESISTANCE |
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25°C/ 70% RH |
|
|
EMC EMISSION |
Compliance to EN55011 (CISPR11), EN55022 (CISPR22) Class B, EN61000-3-2,-3 |
|
|
EMC IMMUNITY |
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN60601-1-2, EN61000-6-2, EN61204-3, heavy industry level, EN61204-3 medical level, criteria A |
|
|
OTHERS |
MTBF |
446.8K hrs min. MIL-HDBK-217F (25°C) |
|
DIMENSION |
127*76.2*31mm (L*W*H) |
|
|
PACKING |
0.26Kg; 63pcs/16.3Kg/1.35CUFT |
|
|
NOTE |
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 ℃of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12″ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives.For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” 5. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time. 6. Heat Sink HS1,HS2,HS3 can not be shorted. 7.Touch current was measured from primary input to DC output 8. Suitable for BF application with appropriate system consideration. |
